GeekVape introduced to the market Zeus X RTA. The novelty is designed for two windings, has an upper air intake, but the lower side blowing of the spirals. In general, the chip of the atom is a double evaporation chamber, the implementation of which, apparently, was strongly reflected in the taste, which is perfectly revealed here.
The Sample box has flown to us for review, so the device will go to the final consumer in a different package, since we, for example, did not have a manual. The set has a spare flat Pyrex glass for 3.5 ml, 810 Ultem drip tip, a bag with a cotton fleece in the form of laces and 2 prewound spirals, a ZIP package, where there are a lot of multi-colored o-rings – only 14 pieces, 8 spare screws, of which 4 under the slot and 4 under the Phillips screwdriver, adapter for 510 drip-types, L-shaped key with hexagonal screws, T-shaped screwdriver and the Zeus X tank itself.
Information for information
GeekVape Zeus X RTA is made of stainless steel and is presented in 6 colors, comes with two glass options – Bubble Glass is pre-installed at 4.5 ml and straight at 3.5 ml, has top air supply, with the ability to adjust the throttle using a ring, but lateral blowing two spirals through a special dome, while coil blown from the bottom.
Vape Wholesale Supply,Vape Wholesale China – AVE40
Height: 47.8 mm (with a drip tip)
Diameter: 25 mm
Volume: 3.5 ml / 4.5 ml
Top mounted drip tip low pro, made of dolrin. It has an unusual, let’s say, design, but is good to use. In general, the hero of the review looks very nice in conjunction with GeekVape Aegig mini .
Inside the drip-type is smoothed under the cone, so the drops of condensate will not be collected from above, but immediately flow down.
The second yellow tipka from ultema also has a narrowing towards the center and is pleasant to use.
Next comes the top cover for refueling atomaizer. It has no threads and previously stood in Zeus RTA and Zeus Dual RTA . Very convenient and fast, just press on top of the top-cap and scroll half a turn and unscrew it. The upper filling has recessed holes that will not allow the liquid drops to remain on top and squeeze out when the top cover is tightened.
Generally Zeus X MOUTH consists of 6 parts: the dome and inside another dome, top cap, tightening adjustment ring, deck and glass.
disassembled parts of the atomizer
The inner part of the cap has a sealing gasket made of silicone for sealing, as well as a key for connection to the shaft.
The top cap is connected to the mine and this is one thing in this tank. A small shaft is inserted inside the shaft, which has holes through which airflow will occur. In general, here the air is first taken from above at an angle through a pair of openings of the cap, then the air moves downward and starts blowing the spirals through the pinholes. Such a realization of air intake, allowed to realize 3 D airflow, i.e. immediately from three sides, and this is perfectly reflected not only in the amount of steam, but also in the taste, which is very clearly revealed here.
Then you can talk about the deck. The base is slightly raised above the deck, i.e. here is the same implementation as in GTA, which means there should be no problems when installing a fleece. In the two racks from the side there are slotted screws that will attract the legs of the spirals.
Two protruding sides can be seen at the base, which will hold the small dome and prevent it from shifting when winding up the large dome with glass. At the very bottom of the pin, which is gilded and quite prominent.
Installing spirals and laying cotton wool
The installation of the spirals here is vertical and this process does not cause any discomfort. If you have a useful tool like the Trimming Tool, then it’s best to keep within 4.5 mm of the leg of the helix. If you do not like the slotted screws, as sometimes it still happens that the screwdriver flies at the time of tightening and you can get hurt, that is, the screws for the hexagon and the key are a poker to help you.
After the screws in the grooves are tightened and the spirals are centered, it’s time to burn them in order to get rid of the dirt that accumulates on them.
Since here the GTA system, the amount of the fleece needs to be measured such that its tips simply fall down through the special grooves in the deck and down the bath.
When laying a fleece, problems should not arise; after it has been laid, remove the hairs in the place where the thread is, in order to avoid biting at the time of assembling the Zeus X.
After wetting the fleece, assembling the atomizer and refueling, it’s time to talk about taste and impressions.
Here’s how the atom looks on Drag mini .
Impressions of use
I really liked the tank, firstly it wasn’t spillage – the slurry wouldn’t go up, secondly, it was a quick refill, the lid was removed very quickly and refilling was done, even with bottles with large nozzles.
About the taste, it can be said that here it is simply revealed perfectly, especially on berry liquids, very tasty. On the installation of cotton wool and how to lay cotton wool – in general there are no questions, everything is simple and clear. Vatu sometimes, depending on the used slurry, can be combed, removed too much.
Cons and pros
– it was not noticed,
– workmanship, threads do not crunch, all parts fit well,
– quick refilling, in half a turn,
-just install two spirals and with the installation of a fleece there are also no problems,
– implementation of non-spill,
– decent taste, very bright colors when opening your liquid,
– compact tank size with a large volume.
Click Here Ave40 For Vape Wholesale Cooperation.
Hot Sale Recommendation:
Vaporesso Aurora Play Zippo Pod Starter Kit
Smok Novo 2 Pod System Kit
Vladdin Eden Vape Pod System Kit
Voopoo Drag Nano Kit
Vaporesso Gen TC Box Mod
Vape Wholesale & buy Electronic Cigarettes online in Bulk. Quality Vape Products, Trusted Vape Wholesale Supply by VapeShops Owners.
WHOLESALE INQUIRY: https://www.ave40.com/wholesale-service.html