GeekVape Zeus X RTA Review

GeekVape introduced to the market Zeus X RTAThe novelty is designed for two windings, has an upper air intake, but the lower side blowing of the spirals. In general, the chip of the atom is a double evaporation chamber, the implementation of which, apparently, was strongly reflected in the taste, which is perfectly revealed here.

vidnabak

Equipment

The Sample box has flown to us for review, so the device will go to the final consumer in a different package, since we, for example, did not have a manual. The set has a spare flat Pyrex glass for 3.5 ml, 810 Ultem drip tip, a bag with a cotton fleece in the form of laces and 2 prewound spirals, a ZIP package, where there are a lot of multi-colored o-rings – only 14 pieces, 8 spare screws, of which 4 under the slot and 4 under the Phillips screwdriver, adapter for 510 drip-types, L-shaped key with hexagonal screws, T-shaped screwdriver and the Zeus X tank itself.

vnabore

vidpaketa

naborcik

Information for information

GeekVape Zeus X RTA is made of stainless steel and is presented in 6 colors, comes with two glass options – Bubble Glass is pre-installed at 4.5 ml and straight at 3.5 ml, has top air supply, with the ability to adjust the throttle using a ring, but lateral blowing two spirals through a special dome, while coil blown from the bottom.

Vape Wholesale Supply,Vape Wholesale China – AVE40

cveta

Dimensions:

Height: 47.8 mm (with a drip tip) 
Diameter: 25 mm 
Volume: 3.5 ml / 4.5 ml

vidvruke

Tank overview

Top mounted drip tip low pro, made of dolrin. It has an unusual, let’s say, design, but is good to use. In general, the hero of the review looks very nice in conjunction with GeekVape Aegig mini .

vidnamode

Inside the drip-type is smoothed under the cone, so the drops of condensate will not be collected from above, but immediately flow down.

The second yellow tipka from ultema also has a narrowing towards the center and is pleasant to use.

vidnadrip

Next comes the top cover for refueling atomaizer. It has no threads and previously stood in Zeus RTA and Zeus Dual RTA . Very convenient and fast, just press on top of the top-cap and scroll half a turn and unscrew it. The upper filling has recessed holes that will not allow the liquid drops to remain on top and squeeze out when the top cover is tightened.

vidzapravki

Generally Zeus X MOUTH consists of 6 parts: the dome and inside another dome, top cap, tightening adjustment ring, deck and glass.

vrazbore

disassembled parts of the atomizer

The inner part of the cap has a sealing gasket made of silicone for sealing, as well as a key for connection to the shaft.

vicap

The top cap is connected to the mine and this is one thing in this tank. A small shaft is inserted inside the shaft, which has holes through which airflow will occur. In general, here the air is first taken from above at an angle through a pair of openings of the cap, then the air moves downward and starts blowing the spirals through the pinholes. Such a realization of air intake, allowed to realize 3 D airflow, i.e. immediately from three sides, and this is perfectly reflected not only in the amount of steam, but also in the taste, which is very clearly revealed here.

vidobduv

vidkupolka vidkuppla

Then you can talk about the deck. The base is slightly raised above the deck, i.e. here is the same implementation as in GTA, which means there should be no problems when installing a fleece. In the two racks from the side there are slotted screws that will attract the legs of the spirals.

vidnabazu

vidnadeku

Two protruding sides can be seen at the base, which will hold the small dome and prevent it from shifting when winding up the large dome with glass. At the very bottom of the pin, which is gilded and quite prominent.

nizpina

Installing spirals and laying cotton wool

The installation of the spirals here is vertical and this process does not cause any discomfort. If you have a useful tool like the Trimming Tool, then it’s best to keep within 4.5 mm of the leg of the helix. If you do not like the slotted screws, as sometimes it still happens that the screwdriver flies at the time of tightening and you can get hurt, that is, the screws for the hexagon and the key are a poker to help you.

bild

After the screws in the grooves are tightened and the spirals are centered, it’s time to burn them in order to get rid of the dirt that accumulates on them.

vidspirali

Since here the GTA system, the amount of the fleece needs to be measured such that its tips simply fall down through the special grooves in the deck and down the bath.

vidhlopka

When laying a fleece, problems should not arise; after it has been laid, remove the hairs in the place where the thread is, in order to avoid biting at the time of assembling the Zeus X.

After wetting the fleece, assembling the atomizer and refueling, it’s time to talk about taste and impressions.

Here’s how the atom looks on Drag mini .

vidnamodika

Impressions of use

I really liked the tank, firstly it wasn’t spillage – the slurry wouldn’t go up, secondly, it was a quick refill, the lid was removed very quickly and refilling was done, even with bottles with large nozzles.

About the taste, it can be said that here it is simply revealed perfectly, especially on berry liquids, very tasty. On the installation of cotton wool and how to lay cotton wool – in general there are no questions, everything is simple and clear. Vatu sometimes, depending on the used slurry, can be combed, removed too much.

Cons and pros

Minuses:

– it was not noticed,

Pros:

– workmanship, threads do not crunch, all parts fit well,

– quick refilling, in half a turn,

-just install two spirals and with the installation of a fleece there are also no problems,

– implementation of non-spill,

– decent taste, very bright colors when opening your liquid,

– compact tank size with a large volume.

Click Here Ave40  For Vape Wholesale Cooperation.

Now It’s Available: GeekVape Zeus X RTA
Hot Sale Recommendation:

Vaporesso Aurora Play Zippo Pod Starter Kit

Smok Novo 2 Pod System Kit

Vladdin Eden Vape Pod System Kit

Voopoo Drag Nano Kit

Vaporesso Gen TC Box Mod

Vape Wholesale & buy Electronic Cigarettes online in Bulk. Quality Vape Products, Trusted Vape Wholesale Supply by VapeShops Owners.

WHOLESALE INQUIRY: https://www.ave40.com/wholesale-service.html

Starter-Kits:https://www.ave40.com/starter-kits/disposable-pod-system-kits

 

 

 

 

ThunderHead Creation Tauren Mech Mod Review

The latest news from Thunderhead Creations.  New mod TAUREN 26mm under (18650/20700/21700)

And hello again, dear vapers and connoisseurs of tasty e-steam. We continue with you to seek out all the most interesting among the vaping devices from manufacturers from around the world. Company Thunderhead Creations we have with you thoroughly examined (designers in the US, manufacturing in China) and are familiar with their devices, which were very good. Today I want to acquaint you with the latest developments of developers with a mechanical mod, which can work from more productive batteries, but if you are not yet sure about the new formats ( 20,700 and 21,700 ), then it doesn’t matter, you can also use the mod with vape batteries format factor 18 650. The mod stands out for its high-quality design and interesting build, besides, the manufacturer asks not so much for such a mod, we are used to seeing high-quality mechanics for as low as $ 100. But here things are simpler. Okay, let’s get this in order.
The latest news from Thunderhead Creations.  New mod TAUREN 26mm under (18650/20700/21700)

So, comes the mod in a black tube with the logo and the inscription of the manufacturer. Inside the tube you will find the mod itself and the keychain in the shape of a key fob all with the same company logo. There is nothing else inside the box. And wait, forget, in the case you will find an adapter, with which the mod can be used with batteries of 18,650.

The latest news from Thunderhead Creations.  New mod TAUREN 26mm under (18650/20700/21700)

The latest news from Thunderhead Creations.  New mod TAUREN 26mm under (18650/20700/21700)

The mod looks great in any version, of which there are several. The main body material is represented by two materials: copper and brass. The inscription of the name of the mod and the logo flaunt on one side, on the opposite side there is a special notch in the case, this solution of the developers allows the vapers to more reliably fix the mod in the palm so that it does not slip out. The button also has a logo engraving. An inscription reminding us of the manufacturer’s company is also engraved near the connector. Each mode is given a unique serial number, which you will also find engraved on the case. Dimensions: as you have probably understood from the title, the diameter of the mod is 26mm, it narrows to the top of the mod, so the seat is approximately 25mm, atomizers with a 24m diameter will look great in tandem with this mod.

The latest news from Thunderhead Creations.  New mod TAUREN 26mm under (18650/20700/21700)

The latest news from Thunderhead Creations.  New mod TAUREN 26mm under (18650/20700/21700)

The latest news from Thunderhead Creations.  New mod TAUREN 26mm under (18650/20700/21700)

The mod is assembled solidly, the button constructive deserves special attention. If you look closely, you can see that the button is made not flush with the case itself, it is as recessed in the case itself. The button itself has a spring mechanism and as they say with an innovative solution of the use of the ball in the design, but we all know that it is not Thunderhead CreationsWere the first who applied this solution design. The button can be disassembled in a matter of seconds, as there are many small components in it, you will often have to clean it. So now the most important thing, as mentioned in the first paragraph. I talked above about the cost, so this mod that you see in the pictures costs $ 40, as for me, this is quite reasonable price. So those who are interested can already safely order and personally test the mod in practice. All thick and tasty, and may steam arrive with you.

The latest news from Thunderhead Creations.  New mod TAUREN 26mm under (18650/20700/21700)

Click Here Ave40  For Vape Wholesale Cooperation.

Now It’s Available: ThunderHead Creation Tauren Mech Mod
Hot Sale Recommendation:

Vaporesso Aurora Play Zippo Pod Starter Kit

Voopoo Alpha Zip TC Kit

Vladdin Eden Vape Pod System Kit

Voopoo Drag Nano Kit

Smok Novo 2 Pod System Kit

Vape Wholesale & buy Electronic Cigarettes online in Bulk. Quality Vape Products, Trusted Vape Wholesale Supply by VapeShops Owners.

WHOLESALE INQUIRY: https://www.ave40.com/wholesale-service.html

Starter-Kits:https://www.ave40.com/starter-kits/disposable-pod-system-kits

Wismec Reuleaux Tinker 2 TC Box Mod Review

Today we will get acquainted with the new version of the Reuleaux Tinker box mod from the well-known company Wismec .

At the end of last year, the popular Chinese manufacturer Wismec  introduced the Reuleaux Tinker box mod , the case of which was styled as basketball sneakers with rubberized inserts. In addition to the remarkable appearance and good ergonomics, the device had a rather solid performance, but it did not gain much popularity among vapers. The other day, the guys from Wismec  decided to give a second chance to the above name and assigned it to their new development, while not forgetting about some useful home chips. We are glad to introduce you to Reuleaux Tinker 2 .

Some distinctive features of the predecessor are easily guessed in the design of the box mod, but the overall concept has undergone significant changes. So, Reuleaux Tinker 2  has protection against moisture, dust and shock according to the IP67 standard, which should save the user from having to worry about the device. From the available colors you can choose one of four options: Titanium gray, Blue & Purple, Black or Red.

In addition to the metal case with soft touch coating, the back surface of the box-mod has received a textured crocodile skin insert, and such a decision should have the best effect on the comfort of holding it.

Inside the Reuleaux Tinker 2 a familiar and familiar board with the same studied functionality is traditionally installed, and the maximum output power of the device is 200W. Interact with the device is offered using a color display with a diagonal of 0.96 inches. On-site and all sorts of variations in temperature control, and the minimum supported resistance in all modes – 0.05Ω .

The novelty works from two replaceable batteries of format 18650, installed through the bottom spring-loaded cover on a special latch. Reuleaux Tinker 2  also allows you to quickly charge batteries with current up to 2A.

The boxmode will be sold both separately and bundled with an unattended tank called Trough , but in all four colors the atomizer will always be painted black.

Features of  Wismec Reuleaux Tinker 2 :

  • Dimensions: 90mm * 53.5mm * 28.5mm
  • Weight: 200,7g
  • Output power: 1-200W
  • Output voltage: 0.5-8V
  • Power supply: 2 * 18650
  • Operating modes: TC-Ni / TC-Ti / TC-SS / TCR (M1, M2, M3) / VW
  • The supported resistance: 0.05-1.5Ω (TC) /0.05-3.5Ω (VW)
  • Charge current: 2A
  • Protection against moisture, dust, shock

Click Here Ave40  For Vape Wholesale Cooperation.

Now It’s Available: Wismec Reuleaux Tinker 2 TC Box Mod
Hot Sale Recommendation:

Vaporesso Aurora Play Zippo Pod Starter Kit

Voopoo Alpha Zip TC Kit

Smok Novo 2 Pod System Kit

Voopoo Drag Nano Kit

Vladdin Eden Vape Pod System Kit

Vape Wholesale & buy Electronic Cigarettes online in Bulk. Quality Vape Products, Trusted Vape Wholesale Supply by VapeShops Owners.

WHOLESALE INQUIRY: https://www.ave40.com/wholesale-service.html

Starter-Kits:https://www.ave40.com/starter-kits/disposable-pod-system-kits

Vapefly Mesh Plus RDA Review

The average user knows almost nothing about Vapefly . This is not surprising, because the guys are not pleased with the special activity in the market. Despite this, every few months they still have a decent device. From what I can remember – Nicolas MTL and Fantasy , working on TFV12 evaporators . Just a few days ago, I learned that the guys had released another product that could be interested in a wide range of Mesh Plus RDA customers .
Mesh Plus RDA by Vapefly -
In atomizers, whose name contains the word Mesh , you can already get confused. Manufacturers are trying to explain as clearly as possible that this is a “grid” atomizer. Vapeflydid not want to stand out, added the word Plus and in production. By the way, it is fair to note that the overall idea of ​​the design here was borrowed from Digiflavor . Despite this, I like dripochka, and I am sure that I like a lot of people like me. The only thing I would advise the company is to add a couple of fresh versions of the hull colors. There are no real photos of a dripka for the time being, so one can only hope that it also looks good in practice.

Mesh Plus RDA by Vapefly -
Dimensions :

Height – 33 mm.
Diameter – 25 mm.
Weight – 45 g.

Specifications :

The first mention of Mesh Plus I saw on the network for quite some time. At that time, there were still no images of the atomizer base, and my first thought was that the Chinese would do everything exactly as the competitors did. But Vapefly surprised me very pleasantly, even though there are a couple of incomprehensible moments here.
Mesh Plus RDA by Vapefly -
So, we have an atomizer, designed for use, as with conventional spirals, and on the grid. The base construct is different from what we saw in such devices, but I’m not sure that it will be more convenient. The fact is that on each side there is one clamp. If there are no problems with spirals, then I’m not sure how practical it will be to fasten the mesh in this way. By the way, pay attention to the grooves under the racks, thanks to them it should be comfortable to cut the legs of the spirals.
Mesh Plus RDA by Vapefly -
Side airflow, represented by two wide slots in a skirt and with an adjustment system in the top cap. Everything seems to be understandable, but I am confused by this one area between the racks. Honestly, I do not understand why she is here at all. If someone understood, then you are welcome in the comments, but they are very interested. What do we have there? Drip type 810 format and, according to tradition, skvonk pin included.
Mesh Plus RDA by Vapefly -

Click Here Ave40  For Vape Wholesale Cooperation.

Now It’s Available:Vapefly Mesh Plus RDA
Hot Sale Recommendation:

Vaporesso Aurora Play Zippo Pod Starter Kit

Justfog Q16Pro Vape Starter Kit

Voopoo Alpha Zip TC Kit

Voopoo Drag Nano Kit

OUMIER Armadillo RDA

Vape Wholesale & buy Electronic Cigarettes online in Bulk. Quality Vape Products, Trusted Vape Wholesale Supply by VapeShops Owners.

WHOLESALE INQUIRY: https://www.ave40.com/wholesale-service.html

Starter-Kits:https://www.ave40.com/starter-kits/disposable-pod-system-kits

How to Clean Toilet bowl brush and Holder

All of us know how important it is to ensure that our toilets remain clean at all times. When I say toilet, I also mean everything that is found in the toilet, such as soap dish, toilet brush and toilet bowl brush and holder. To ensure that the toilet is as clean as it can possibly be, your toilet bowl brush holder and other items in the toilet need to be very clean as well.

In this post, we have focused on the toilet bowl brush holder and holder and how to clean it. Read on to find out easy and quick ways to clean this important item.

The most efficient method

The most efficient cleaning method is to soak your toilet bowl brush and holder in bleach. It is advisable that you start by reading the product label for the application instructions before you apply this cleaning technique. Be sure to pay attention to any given safety guidelines. This is important because bleach is a very powerful product.

You will need the following to apply this cleaning technique:

  • Bleach
  • Bucket or container
  • Rubber gloves

On rubber gloves, you should only use the pair that you have set aside for toilet cleaning purposes. You should never use rubber gloves that you usually use to clean the dishes to clean the toilet.

First, fill the bucket or any container you are using with hot water. Next, add 2 to 3 capsules of bleach. You should also check the bleach bottle label for any piece of advice on how many capsules you should add to what amount of hot water.

Secondly, put your toilet bowl brush and holder in the bucket with hot water mixed with bleach. Leave it for about an hour.


Wall Mounted Brush Holder

Thirdly, take out the brush and holder out of the bucket or container and then rinse using hot water. Leave both the bowl brush and holder for sometimes to dry before you can put the brush back into the holder. You can place the item in some raised place in the toilet for about 10 minutes or so to allow it to drain off and dry.

Free Standing Brush Holder
Free Standing Brush Holder

Alternatively, you can use domestic bleach spray or any disinfectant spray to spritz the outside and inside of the toilet brush holder. If you want, you can also soak your toilet bowl brush and holder in bleach solution for about an hour just as mentioned earlier.

Key points to note

  • Clean water and bleach are key to cleaning a toilet bowl brush and holder
  • You can always use disinfectant spray or bleach for your toilet brush bowel and holder.
  • Always wear rubber gloves whenever you are using bleach

It is recommended that you clean your toilet bowl brush and holder on a regular basis to avoid bacteria build up. Precisely, you can do the cleaning once a week, or every time you clean your toilet. Doing so using the quick method we have explained above will definitely result in clean and hygienic bathroom.

8 Best Toilet Brushes 2019 – Reviews & Comparison – Pick A Toilet!
https://www.pickatoilet.com/
Rating: 3 – 53 votes
Jump to – InterDesign Duetto Toilet Bowl Brush and Holder – The same is seen in the case of InterDesign Duetto Toilet Bowl Brush and Holder that has a …

VapeMons Gear 222W TC Box Mod Review

Surely the Vapemons brand is unfamiliar to you. So it was with me until recently, but less than six months from the moment of our acquaintance, their novelty crawled to me, which now you can’t name. I want to note that this is the flagship boxing mod of the manufacturer, except that you rarely find its products. Nevertheless, we meet, he has a couple of chips. 

Vapemons GEARbox mod Dimensions: 92.5 x 56.5 x 28mm Weight: 151g Case material: stainless steel Power supply: 2 x 18650 Chipset: VM Omni board 4.0 Output power: 5 – 226W Operating mode: POWER, TC (NI200, SS, TI), BYPASS Temperature range: 200 ℉ – 600 ℉ / 100 ℃ – 315 ℃

 
Supported resistance: 0.03 – 5.0Ω (Super Player Mode Only) 
Protection: from low / high resistance, from overheating, from short circuit, from incorrect polarity, from overcharging / overdischarge 
Connector type: steel 510, pin gold-plated, spring-loaded 
Screen / diagonal: yes, 0.96 ” 
Micro-USB port / charging: yes, charging current 0.75A wired, 1.4A wireless 
Color: see photo below Package contents – GEAR box mod mod – USB cable – user manual – docking station for wireless charging

 
 
Our guest looks good – there are original elements, such as control gear and panels with a kind of pattern. I will not say that you have a special pleasure, holding it for the first time in your hands. Yes, it looks interesting – but every now and then there are flaws in the quality of the performance (I’ll tell you about them along the way) and the panels, although the print is rather interesting, they look somehow cheap. Although still if you abstract, the normal mode is average. The landing area of ​​steel, on it the Star of David is engraved, it seems to be the name. It rises a little above the main body, therefore, the atoms do not crawl over it, the paintwork of which, by the way, is very prone to scratches. The maximum aesthetic fit is provided only to atoms 24mm in diameter, despite the greater width.

 
The control gear replaced the plus and minus buttons, as well as the function of hover mode switching on it. The notches on it are spiky, but not too much, the stroke is smooth, stepped. It is quite comfortable to use. It also has a built-in LED indicator. The control panel consists of a metal button with a concave profile and a small display. As for the first, it is convenient in principle, a small move, a loud click. But she is so godlessly dangling in a metal case and, accordingly, jingles that sometimes I don’t even want to take the box mod.

 
 
The display is quite bright, the information provides articulately. But even here it was not without the “podlyany” – in my case it is set crookedly relative to the notch in the body. Therefore, even non-serviceable areas can be seen. I admit that this is an isolated case, but the sediment remained, anyway. Immediately at the base of the control panel you can see the connector for charging batteries, charging through this port is carried out by a small current of 0.75A. Plus, there is the possibility of wireless charging, and there is a docking station for this purpose. It is small – diameter 100mm. There is a connector for the lace and LED display on the perimeter.

 
 
Wireless charging is also not so smooth, basically it gives out about 1.4A, but sometimes it even goes up to 2.2A. Rarely, but it happens that this indicator jumps. I am not particularly an experienced user of wireless charging – perhaps these are its features. In order for the box to be charged, it must be put on the docking station with the butt end of the gear. In general, the feature is convenient and it works. Behind the removable side panel, which is fixed by six magnets and sits securely, almost without play, the compartment for the battery hides. There is a key in its base for easy removal. The contacts are probably gilded and well spring-loaded, however, they are costly to handle the batteries. Ribbon for convenience provided.

 
 
Well, now let’s work on the chipset. As you noticed, it is called Omni board 4.0. I, too, at first was surprised and delighted – after all, it was precisely such people who use Vaporess. However, the joy was short-lived – I did not pay attention to the postscript at the beginning, namely “VM or Vapemons”. So, we probably have our own manufacturer. In general, the functionality is not bad, and its management is decent, but there are flaws in the work.

 
Resistance often jumps and even if only on units of hundredths of an ohm, but somehow it is not particularly pleasant. In terms of output power, it seemed to me, the mod significantly imparts, that is, the actual wattage is less than the displayed value. Plus, the chipset often goes into protection against overheating – the words “too hot”. And on Dripke with Sapra 0.1, this happens literally a field of several puffs from a cold start. And that’s not all – I even achieved this unpleasant inscription by driving a 17W tank to tank, although it took a lot more puffs. Plus, during operation there is a decent heating of the mod in the area of ​​the charging connector. Impressions of use


An interesting box, however, he completely disappointed me – it is understandable, if at least the managing chipset worked without any complaints, it was possible to turn a blind eye to the flaws in the quality of execution. And so there is nothing to say, and the price tag is not to say that it is tempting. And yet I found a couple of cherries even with this – this is an original construct and the possibility of wireless charging. Perhaps I will refrain from recommendations this time. 

Package Included:

1 x Gearbox mod

1 x Wireless charging pad

1 x Warranty Card&User manual

1 x Gift box

Click Here Ave40  For Vape Wholesale Cooperation.

Now It’s Available: VapeMons Gear 222W TC Box Mod
Hot Sale Recommendation:

Vaporesso Aurora Play Zippo Pod Starter Kit

Voopoo Drag 2 Platinum 177W TC Box Mod

Vladdin Eden Vape Pod System Kit

Voopoo Drag Nano Kit

Vaporesso Gen TC Box Mod

Vape Wholesale & buy Electronic Cigarettes online in Bulk. Quality Vape Products, Trusted Vape Wholesale Supply by VapeShops Owners.

WHOLESALE INQUIRY: https://www.ave40.com/wholesale-service.html

Smok TFV16 Mesh Tank Review

Novelty from the company Smok – subomnom atomizer TFV16Chip tank is a large volume that can fit 9 ml of fluid, as well as a modified system of air intake. Also, the manufacturer took care of 3 types of evaporators on the grid.

vidbakka

Equipment

TFV16 Tank with 9 ml glass, TFV16 Mesh 0.17 Ohm Coil (initially installed in the tank), TFV16 Mesh 0.12 Ohm Coil, protective silicone case for bubble glass, glass with reduced volume, spare parts kit, instructions.

gabaritt

Information for information

Smok TFV16 is made of stainless steel and is available on the day of writing the article in 6 colors, equipped with a non-standard drip-type made of Resin, the top cover of the filling, increased volume in 9 ml thanks to bubble-glass, lower adjustable blowing, new TFV16 Mesh Coil evaporators. Atomizer is designed for bulk.

Dimensions

Height: 64.5 mm 
Base diameter: 27 mm (28 mm with an adjusting ring), 
Diameter: 32 mm with 9 mm glass (27 with reduced glass), 
Weight: 94 g 
Volume: 9 ml.

gabirittu

Tank overview

Like previous campaign creations from the TFV line, the tank is made of stainless steel. Available in the following colors: Black Plating, Red, Blue, Gold, Stainless Steel, 7-Color.

cvettoa

On top of the atomizer there is an epoxy resin company’s own drip type. It is an external nozzle with a diameter of 16 mm. Therefore, for the change will have to wait until Smok present a line of interchangeable devices for customization. It is not clear the decision of the manufacturer, since the previous models, for example TFV12, had an o-ring, but still a standard 810 drip tip, which could be found if desired. Perhaps in TFV16 will be their drip-types, which will appear in the near future on the site.

verhdripa

The filling system is carried out using a sliding top cover, which is mounted on the latch. For refueling we have one hole of average diameter. There is also a lock on the side that does not allow the tank to open when carried.

zaliffgiga

Initially, the tank comes with a 9 ml bubble glass, for the protection of which a special silicone ring with perforation was invented. But the kit also comes with the usual version of the flask with a smaller volume.

sravni

Adjustment of the blower takes place thanks to a ring with two large holes. And according to the manufacturer, the air intake system is now different than it was in the TFV12 Prince tank . As can be seen in the figure above, the air will flow intensively into the evaporation chamber, which should quickly reveal the taste of liquids.

isparriku
For the tank also presented a new series of replaceable evaporators on the grid. The following models are available: TFV16 Mesh Coil 0.17 ohms for a power of 120 watts, TFV16 Dual Mesh Coil 0.12 ohms for a power of 120 watts, both supplied with a tank. Separately sold model TFV16 Triple Mesh Coil 0.15 ohms for power of 90 watts. You may notice that the holes for the slurry are really large, so problems should not arise with impregnability!

vidnaisparr

Pin bulges medium, and very few people use this kind of atomizers on mechmods.

Click Here Ave40  For Vape Wholesale Cooperation.

Now It’s Available: Smok TFV16 Mesh Tank
Hot Sale Recommendation:

Vaporesso Aurora Play Zippo Pod Starter Kit

Vaporesso Gen TC Box Mod

Voopoo Alpha Zip TC Kit

Voopoo Drag Nano Kit

OUMIER Armadillo RDA

Vape Wholesale & buy Electronic Cigarettes online in Bulk. Quality Vape Products, Trusted Vape Wholesale Supply by VapeShops Owners.

WHOLESALE INQUIRY: https://www.ave40.com/wholesale-service.html

KangerTech GEM Vape Pod System kit Review

The twentieth day of our campaign “Not a Day without AIO” was marked by another novelty in the “lowest” price segment. This time, the novelty awaits us in the camp of old-timers – the company Kangertech. These guys know a lot about starter kits, but their design spark seems to be permanently stuck in the past. However, this time they will present a novelty that meets all the latest trends.

Kangertech GEM Pod 
Kangertech GEM Pod -
Dimensions: 80 x 32 x 14mm
Weight: unknown
Case material: plastic + metal
Power supply: built-in 500mAh
Cartridge capacity: 2ml
Evaporator resistance: 1.2Ω
Output power: 11.5W
Voltage range: 3.7V
Mode of operation: the POWER
protection: Low / high resistance, overheating, short-circuit, overcharge / overdischarge
Connector Type: Magnetic
Shield / diagonal: No
Micro-USB port / charging: there, the charge current is unknown
Color: see photo below
Kangertech GEM Pod -
Options
– GEM mod
– replaceable cartridge (preinstalled)
– USB cable
– user manual
– warranty card
Kangertech GEM Pod -
The appearance of our hero is quite decent – the developers didn’t think much and just performed a completely regular oblate shape. You will not find any decor here – it has gone to a novelty only in favor.
Kangertech GEM Pod -
Dimensions are small – it is definitely worth counting on a certain stealth.
Kangertech GEM Pod -
The color palette is already full of suggestions from the start – there will be six of them altogether, but only the colors of the case will change. Dark colors will prevail in all variants.
Kangertech GEM Pod -
Replaceable cartridge standard for the segment accessory capacity. It will refuel from the bottom, the hole is plugged with a plastic plug.
Kangertech GEM Pod -
Built-in evaporator on ceramics, designed so naturally for liquids with salt nicotine. Magnetic fixation.
Kangertech GEM Pod -
The main body hides inside a built-in battery of a small capacity – it seems that it would be possible to shove more. The hole for its charging developers defined at the bottom. However, the cycle time of its full charge is not disclosed.
Kangertech GEM Pod -
Fire buttons on the device body is not provided – it is activated by tightening. But there is an informative LED indicator – it will be responsible for the feedback of the device with its newly-made owner.
Kangertech GEM Pod -
Price $ 20.9

Click Here Ave40  For Vape Wholesale Cooperation.

Now It’s Available: KangerTech GEM Vape Pod System kit
Hot Sale Recommendation:

Vaporesso Aurora Play Zippo Pod Starter Kit

Geekvape Aegis Solo TC Box Mod

Voopoo & Woody Vape X217 217W TC Box Mod

Voopoo Drag Nano Kit

OUMIER Armadillo RDA

Vape Wholesale & buy Electronic Cigarettes online in Bulk. Quality Vape Products, Trusted Vape Wholesale Supply by VapeShops Owners.

WHOLESALE INQUIRY: https://www.ave40.com/wholesale-service.html

Wismec Trough Subohm Mesh Tank Review

Wismec has released Trough Sub Ohm Tank. The maintenance-free tank was covered with environmentally friendly paint, and it was also equipped with a pair of new evaporators on the nets and “bellied” glass with a volume of 6.5 ml.

On June 5, Wismec announced Trough Sub Ohm Tank on Instagram . The steel case of the new tank was distinguished by an innovative coating, as the developers note – it was applied by vacuum deposition, retains color and texture well, and is also environmentally friendly. The choice provided four familiar colors – black, gold, steel and rainbow. The shifting cover was supplied with anthracite driptyp and girded with a ring with rough edges. At the base, they fixed a “duty” ring with wide air holes.

The device works with brand evaporators from a new line, they are “stuffed” with organic cotton, support a circular fluid distribution system and are calculated for one, two or three grids with a resistance of 0.35; 0.2 and 0.15 ohms, a triple-wound specimen is not provided for in the standard kit. The volume of a flask will make 6,5 or 2 ml depending on the chosen version.

The device comes in a transparent box with two evaporators, a set of spare parts and instructions.

Main characteristics:

  • Height – 50 mm
  • Diameter – 30 mm
  • Weight – 61.5 g
  • Volume – 6.5 / 2 ml
  • Top dressing
  • Adjustable airflow

Parameters of Wismec Trough Subohm Mesh Tank 6.5ml

Features:

Exquisite appearance with EFVP technology
360° Diversion e-liquid leading system
WT mesh coils, restore The most authentic e-liquid flavor
30% Wood Pulp and 70% Organic Cotton for better flavor
Large airflow slot & Adjustable airflow control system
Various tank versions available for your Preference

Package Included:

1 x Trough
1 x WT01 Single 0.35ohm Head
1 x WT02 Dual 0.2ohm Head
1 x User Manual
Spare Parts

Package Included of Wismec Trough Subohm Mesh Tank 6.5ml

Click Here Ave40  For Vape Wholesale Cooperation.

Now It’s Available:Wismec Trough Subohm Mesh Tank
Hot Sale Recommendation:

Vaporesso Aurora Play Zippo Pod Starter Kit

OUMIER WASP Nano RTA

Smok Vape Pen Nord 19 Tank

Voopoo Drag Nano Kit

OUMIER Armadillo RDA

Vape Wholesale & buy Electronic Cigarettes online in Bulk. Quality Vape Products, Trusted Vape Wholesale Supply by VapeShops Owners.

WHOLESALE INQUIRY: https://www.ave40.com/wholesale-service.html